Posts Tagged ‘service’

So I am getting close to finishing the bike up. So in this garage session I have tackled the last few bits of work I have left. This afternoon I had some help so there aren’t many pictures. First of all I have changed the clutch master oil. I have used a BelRay 2,5w fork oil in it and it works great.

This is where I left off in part 2
IMG_4754

Next I have oiled a new Twin-air air filter and threw the old one away.
IMG_4746
IMG_4748
IMG_4749

I got a new battery under warranty installed it and tried the e-start for the first time in I guess 2 years, according to PO when I bought the bike. It turned the engine, which was great to hear.
IMG_4751

That out of the way, I turned my attention to the most ridiculous and complicated oil change process ever invented. I think those Austrian engineers were drunk or had a serious hangover when they designed the oil system on LC4’s. Luckily there are good people on advrider.com that has made things more clear, but still it took a lot of time.

I have use KTM OEM filters and gasket, with BelRay Thumper Racing Syn Ester Blend 4T Engine Oil 15W-50.
IMG_4755

Last oil change on this bike, looking at the date I found on the small inside filter, was 13.6.2014, its good to know that the bike had fresh oil in regular intervals. But I guess PO didn’t have any idea what is with the plugs on the bottom of the engine as the situation there has scared me a bit. Do you see that error?
IMG_4756

He has put the oil drain plug, with the spring in the by-pass valve hole, and the plug for the by-pass valve in to oil drain plug. I have tried correcting the mistake but the threads wouldn’t engage the oil drain plug in it’s rightful hole, so I had to leave it as it was.

Last, but not least, I have changed most of the the bolts that hold the plastics on with new ones.
IMG_4757

Last thing I have to do is change the chain and sprockets on the weekend if I will have any time.

Stay safe!

Advertisements

To continue where I have left off in part 1. I have gone ahead and changed the brake fluid in the rear brakes. Doing brake fluid change is a lot easier if you have a spare set of hands to help on one side since master cylinder is on different side than the caliper.
IMG_4699

This bike will be for solo riding only, no passenger like on KLE, so I have removed the rear foot pegs. I have left the peg hangars in place as they are a good tie down point for luggage.
IMG_4701
IMG_4702

Than I have decided to change a spark plug. But trying to get it out with my socket proved impossible. I needed a serious extension to get it undone.
IMG_4722

It was tight and rusted, probably still the OEM one from years back.
IMG_4725

I have seen a few occasions where people have lost their shifter levers. So I have drilled a 1,5 mm hole through the bolt head and safety wire it to the lever itself so it can not get lose and fall off.
IMG_4703

Next on the list was to tidy up the engine bay and get rid of all the non-essential crap in there. I have checked the engine over and saw that previous owner has removed SAS from the bike, which is great, less work for me. But the EPC was still there. You can find info on both system on the links provided.

So this is what you take off the bike. Note that the 90 degree pipe and the little filter have to go back on the bike. The EPC unit and the hoses on the right go to the shelf.
IMG_4719

I have tucked the small filter in behind the rear brake fluid cup. Fits nicely out of the way.
IMG_4721

Before…
IMAG0595

…after. It looks a lot cleaner now, still need to sort out all the disconnected wires and tie them somewhere safe.
IMG_4718

Than I have tackled those really old coolant pipes. I have ordered a set of orange pipes to replace the old black ones.
IMG_4698

I started removing and replacing those hoses one by one. It was quite hard to get some of those hoses off because of all the grime inside on the fittings.
IMG_4729

I have replaced all the hoses but one, which didn’t have a jubilee clip but some soft of permanently clamped metal strap and I didn’t want to mess with it.
IMG_4732
IMG_4743
IMG_4741
IMG_4742

That is it for part 2. Stay tuned for part 3 where I hopefully finish the bike and take it for a spin.

Stay safe!

Spring and warmer temperatures are just around the corner and it is time to sort out the bike for this riding season. I have spent the whole afternoon in the garage today and got a lot done, but I ran out of electricity just before I could finish all my objectives for today.

I have quite a lot to do before I can start ridding. Through this series of posts I will be doing the following things:
-Refresh all fluids
-New filters all round
-New chain and sprockets with 15/44 gearing instead of 16/42
-Swapping clutch and brake levers
-New coolant hoses if they arrive
-New battery
-Sprag clutch replacement
-New throttle tube
-Spark plug

I have probably forgot something but who cares, it’s a long list and I better get to it.
IMG_4665

First on the list was finding out where the clutch is leaking. Or so I thought. I cleaned all the grime on the outside off and expected to find a half empty master cylinder, but when I loosened the bolts It was overfilled, so I guess no leaks. Next on the list was a new clutch lever. I ordered a short lever (54602031000
) because I didn’t want to cut the old ones.
IMG_4666

Looking at the pivot point, 12 years of use have left a mark on it.
IMG_4668

That is the clutch side almost done, still waiting for rubber boot and insert in the master cylinder. But it’s looking good.
IMG_4669

Than I have moved over to the brake side. Same as with the clutch, I got short lever for the front brakes (50313002100).
IMG_4670

Brembo even supplied a HUGE paper instructions
IMG_4671

Old and new lever. You need to swap over the push pin.
IMG_4672

Next I moved to a little something of a improvement, instead of regular maintenance. Since throttle is a little jerky on the 640 I bought a KTM Powerparts Throttle Cam system to try and tame it a little.
IMG_4677
IMG_4678

First order of business was removing the grip from the old tube without damage. So I pushed in a screwdriver a little and spray some WD-40 inside. Work it around and deeper in, add WD-40 and repeat. All the way to through the whole grip. and it will slide off without any damage. Make sure you degrease it before reinstalling it on the new throttle tube.
IMG_4673
IMG_4674

Now you can slide the rubber boot off the cables and undo the bolts keeping the throttle assembly together. Disconnect the cables and remove the old plastic tube. Once off, be sure to clean the bars thoroughly before moving on.
IMG_4681
IMG_4683
IMG_4684

Here is the KTM throttle tube with a 200 cam on it that I will try first. You get 3 in the set, stock one a 200 and 400 cams, which have altered cable pull.
IMG_4679
IMG_4680

When you put everything together make sure nothing binds and throttle snaps back as it should. There is no need to adjust any cables. Tighten everything back together and replace the rubber boot.
IMG_4687
IMG_4688
IMG_4689

Next on the list was to replace those rubber inserts in the triple clamps that hold the handlebar clamps on. They were old, damaged and hard.
IMG_4694

Now instead of getting a new set of rubber inserts, I have opted for a solid mounted version and got aluminium inserts. There are some benefits and some drawback to this.
IMG_4693

The swap is a so straight forward that I won’t describe it. Just take a look at the pictures and you should be able to figure it out.
IMG_4691
IMG_4695
IMG_4696

After securing the bars back to the bike I decided the next thing to take care is the brake fluid. I only managed to do the front as my battery that powers my lights has died, so I will be doing the rear brake in next garage sitting. This was inside the front master cylinder, not to bad.
IMG_4697

Stay tuned for part 2.